.png/:/rs=w:400,cg:true,m)
Not your typical WiFi devices.
This Security series offers an alternative to consumer-based Wi-Fi devices that require a monthly service contract.
This system can integrate with our Video Recording systems which offers longer term video storage that can be accessed with mobile devices and computers.
Snapshot from the Floodlight from the office.
Snapshot from the video doorbell
Snapshot from the Wi-Fi camera
1080p Wi-Fi Floodlight Camera
1080p Wi-Fi Floodlight Camera
1080p Wi-Fi Floodlight Camera
The camera offers Passive IR motion detection and is capable of sounding a siren and turning on a floodlight when an intruder is detected.
- 1/2.7-in. 2MP Progressive-scan CMOS Sensor
- 2.4 GHz, IEEE802.11b/g/n, 100 m
- (328 ft) Open Field WiFi
- H.265 and H.264 Dual Codecs
- 2MP at 30 fps Maximum Resolution; 2.8 mm Fixed Lens
- Built-in Microphone and Speaker
- Active Alarm with Integrated 110 dB Siren and Floodlight
- Maximum IR LED Length 10 m (33 ft)
- IP65 Ingress Protection
- Micro SD slot 256 GB
- Powered by Wire
1080p WiFi Video Doorbell
1080p Wi-Fi Floodlight Camera
1080p Wi-Fi Floodlight Camera
WiFi Video Doorbell is a component of the Dahua LincX2PRO camera series. The doorbell offers Passive IR motion detection and transmits video and audio to a mobile phone for remote visual confirmation and communication with visitors
- 1/2.7-in. 2MP Progressive-scan CMOS Sensor
- 2.4 GHz, IEEE802.11b/g/n, 100 m
- (328 ft) Open Field WiFi
- H.264 Video Compression
- 2MP at 20 fps Maximum Resolution
- 1.9 mm Fixed Lens
- Built-in Microphone and Speaker for Real-time Communication
- PIR Detection
- Maximum IR LED Length 5.0 m
- (16.50 ft)
- Micro SD slot 64 GB
- Powered by Wire
1080p Wi-Fi Mini Camera
1080p Wi-Fi Floodlight Camera
1080p Wi-Fi Mini Camera
The camera offers Passive IR motion detection and is capable of sounding a siren and turning on a spotlight when an intruder is detected. making it the ideal camera for indoor and outdoor surveillance at homes and small retail or dining establishments.
- 1/2.7-in. 2MP Progressive-scan CMOS Sensor
- 2.4 GHz, IEEE802.11b/g/n, 100 m
- (328 ft) Open Field WiFi
- H.265 and H.264 Dual Codecs
- 2MP at 30 fps Maximum Resolution
- 2.8 mm Fixed Lens
- Passive IR Detector
- Built-in Microphone and Speaker
- Active Alarm with Integrated 110 dB Siren and Spotlight
- Maximum IR LED Length 10 m (33 ft)
- IP65 Ingress Protection
- Micro SD slot 128 GB
- Powered by Wire
video doorbell installation
1
If not already done, disconnect the wire from the existing doorbell, that goes between it and the "FRONT" terminal on the door chime.
Disconnect the wire from the exisiting doorbell, that goes between it and the Power Transformer.
2
Flip over the DB11 and connect the Wire Harness wires, included in the box, to the back of DB11
3
From the DB11 and the door chime, twist the two wires, one from the end of the Wire Harness and one from the door chime, and connect them together with a Wire Nut or Clip (included in the box).
Repeat this for the other set of wires from the DB11 and the Power Transformer.
4
The door chime that is already installed will either be Electronic or Mechanical. Make sure the two wires are already connected to the FRONT and TRANS connections. If they are not, adjust them so they are.
5
If you are using a Mechanical door chime skip to Step 7. If you are using an Electronic door chrime continue from here.
6
Connect the wire set shown below (included in the box) to the Chime Kit with the green Terminal Block (also included in the box).
Connect the wire set in line with the DB11, door chime, and AC Power Transformer in the configuration.
8
Open your mobile app and you MUST follow instruction below to complete your Door Chime Setup.